Elastic (Up To 200% Elongation) 3D Printer Resin – Translucent Blue 500G

AUD78.95 Inc GST

Tearing resistanceWear-resisting

Anti-folding

Fast bouncing back

Elongation at break up to 200%

 

In stock (can be backordered)

Quantity Discount (%) Price
1 - 19 AUD78.95
20+ 10 % AUD71.06
x
SKU: 602024399599 Categories: , Tags: , , , , ,

Description

Elastic (Up To 200% Elongation) 3D Printer Resin – Translucent Blue 500G

 

Technical Data Sheet

Product detail

Model number? ELA series

Product advantage:

 

Non VOC, RoHS certificated

Compatible for most 3D printer

 

Technical specification?

Volume shrinkage?3.35%-5.65% Elongation at break?100-150%
Linear shrinkage?1.05-1.35% Hardness(Shore D)?10-15 D
Tensile strength?40-70MPa 405nm
Tensile modulus?1.882?2.385 MPa
Glass transition temp.?100?
Density?1.05?1.25 g/cm3
Notched impact strength:41-48j/m
Viscosity?300-800MPa?s

 

Printing parameter

 

For LCD printer, bottom layer 20-70s and each layer exposure time?4-20s, for example, layer thickness 50 micron on Anycubic printer, base 35s while each layer 15s.

For DLP printer, bottom 5-15s and each layer 1-6s.

The?exposure?time should be adjusted according to printer light energy, layer thickness and model structure.

 

Cleaning and post-curing

  1. For Regular resin:

Step1, Spray with Isopropanol, then blow resin away with cool wind.

Step2, Prepare two containers with Isopropanol (alcohol> 95%), and place the jobs into the first container and slightly shake it, then soak in the second container for about 1 minute (dental resin should not exceed 30 seconds).

Step3, Flush with water before dry it, do make it sure it ?s 100% dried as residuary alcohol may cause white spot or crack on jobs.

  1. For high wax resin (cwic ewic):

Step 1, keep the prints on the flatform, and wipe away the resin on the flatform with tissue.

Step2, Spray the alcohol on the prints and blow it with cool air.

Step3, Repeat it until it is clean.

Note: Do not dip in alcohol too long as it may crack and with white spot.

  1. Water washable resin:

Cleaning with flush water and brush it gently with a soft brush, and then drying it with cold air.

NOTE: 1. Do not use ultrasonic for cleaning, especially for casting resin.

  1. Dental resin jobs are recommended to be cleaned before take off from the platform to avoid deformation.

?

Post-curing:?

  1. The curing time is proportional to the volume of the work piece and inversely proportional to the optical power of the curing chamber. Example: 100 watt LED curing box, jewelry jobs is recommended to be cured with soaking in water for 20-30 minutes.
  2. The post-cure time of dental casting resin, dental non-casting resin and jewelry mold resin shall not more than 5 minutes.
  3. Work-pieces should be in the water during post-curing to prevent deformation especially for dental and jewelry.
  4. Don?t forget to use cool air to dry it after post-curing.

 

 

Warning?

  1. This material should not be in contact with eyes, skin or clothing, and should not be tasted or eaten.
  2. If you accidentally touch your eyes or skin, immediately rinse with water for about 20 minutes and seek medical advice if necessary.
  3. Please pay attention to air circulation and take protective measures when using. Wash thoroughly after handling.
  4. The product is in a liquid state with a slight odor. Wear a mask and gloves.
  5. The product should be stored in a sealed container. After use, it should be filtered and keep back in bottle on time and placed in a dry and well ventilated place. It should not be exposed to sunlight.
  6. Shake well before use, and leave it for 30 minutes to eliminate air bubbles that generated during the shaking process.
  7. The ambient temperature is recommended to be controlled at 25-30 degrees Celsius, and during the printing should avoid any lights.
  8. Dispose of waste in accordance with local environmental regulations.
  9. Storage environment: Store in cool and dry place, and avoid sunlight, recommended temperature at 25-30 degrees Celsius.

 

Additional information

Weight 1 kg
Dimensions 10 × 10 × 25 cm

Brand

Jamghe

Shenzhen Yongchanghe Technology Co., Ltd. is a subsidiary corporation of Meilianxing (stock code: 871919), which specialized in the Rearch and develop UV light curing since 2001, self-branding Jamg He dedicate to supplying our customers with the world-leading 3D printing solution. We creatively adhere to explore potential applications of 3D printing resin into different fields such as jewelry, dental, medical, aerospace, engineering etc. Three Production Bases With decades experience built 3 international standardized production bases(Shenzhen, Jiangxi, Yangjiang), allow us to offer diversified resins at high quality for DLP, SLA and LCD printer. Invention Patent for 3D Resin This is the secret why JAMG HE 3D resins are great performance with smooth surface, high accurate, stability and all of resins are non solvent. Strong R & D Team Self own three experiment labs with hi-end equipment, also cooperate with academic institution built additive manufacturinglabs in different cities.