-
- 1.75mm filament
Aurarum PLA 3D Printer Filament – Sky Blue 1.75mm 1Kg
- AUD25.56 - AUD31.95 Inc GST
- Aurarum PLA is the easiest material to print with ? A good starting point for a successful print is to have your hot end around 200 degrees and your hot bed around 55 degrees. All AURARUM filaments are 100% Australian made right here in Melbourne, Victoria.
- Add to cart
-
- 2.85mm filament
Aurarum ABS 3D Printer Filament – Silver 2.85mm 1Kg
- AUD22.36 - AUD27.95 Inc GST
- Aurarum ABS is an easy material to print with provided you have a heated bed and sealed chamber. A good starting point for a successful print is to have your hot end around 235degrees and your hot bed around 100 degrees. All AURARUM filaments are 100% Australian made right here in Melbourne, Victoria. Aurarum Brand
- Add to cart
-
- Electronics
BIGTREETECH PI TFT50 V2.0 screen board
- AUD134.95 Inc GST
- 32 bit controller board comes with DCDC mode v1.0, Wifi module, 3.5" TFT v3.0 and 5pcs TMC2209
- Add to cart
-
- 2.85mm filament
Aurarum ABS 3D Printer Filament – Red 2.85mm 1Kg
- AUD22.36 - AUD27.95 Inc GST
- Aurarum ABS is an easy material to print with provided you have a heated bed and sealed chamber. A good starting point for a successful print is to have your hot end around 235degrees and your hot bed around 100 degrees. All AURARUM filaments are 100% Australian made right here in Melbourne, Victoria. Aurarum Brand
- Add to cart
-
- Electronics
Makerbase MKS DLP SLA UV LCD Resin 3D Printer kit with Sharp 2K LCD
- AUD149.50 Inc GST
- All in one DIY 3D SLA DLP printer solution. No need for a complicated Raspberry Pi+shield or Raspberry Pi+mega board solution. This kit comes as a set for your project - Motherboard, LCD for control and the 2K Sharp TFT for your bed.
- Add to cart
-
- Electronics
3pcs NTC Thermistor 100Kohm Sensor 3D Printer
- AUD12.95 Inc GST
- This thermistor comes with ptfe tubing on its connectors and 1m long leads attached to it.
- Add to cart
-
- Out of Stock
- Electronics, Stepper motors
1.8degrees Nema 17 stepper motor, 8.2 kg.cm holding torque, D dual shaft
- AUD29.95 Inc GST
- Nema 17 stepper motor, 8.2 kg.cm holding torque, D dual shaft 1.8 degrees
- Read more
-
-
- 1.75mm filament
Aurarum PLA 3D Printer Filament – Yellow 1.75mm 1Kg
- AUD25.56 - AUD31.95 Inc GST
- Aurarum PLA is the easiest material to print with ? A good starting point for a successful print is to have your hot end around 200 degrees and your hot bed around 55 degrees. All AURARUM filaments are 100% Australian made right here in Melbourne, Victoria.
- Add to cart
-
- 1.75mm filament
Aurarum PETG 3D Printer Filament – Baby Blue 1.75mm 1Kg
- AUD25.56 - AUD31.95 Inc GST
- Aurarum PETG is a moderately easy material to print with provided you have a heated and well levelled bed. A good starting point for a successful print is to have your hot end around 235 degrees and your hot bed around 70 degrees. All AURARUM filaments are 100% Australian made right here in Melbourne, Victoria.
- Add to cart
-
- 1.75mm filament
Aurarum PETG 3D Printer Filament – Baby Pink 1.75mm 1Kg
- AUD26.36 - AUD32.95 Inc GST
- Aurarum PETG is a moderately easy material to print with provided you have a heated and well levelled bed. A good starting point for a successful print is to have your hot end around 235 degrees and your hot bed around 70 degrees. All AURARUM filaments are 100% Australian made right here in Melbourne, Victoria.
- Add to cart
-
- 1.75mm filament
Aurarum PETG 3D Printer Filament – Botanical Green 1.75mm 1Kg
- AUD25.56 - AUD31.95 Inc GST
- Aurarum PETG is a moderately easy material to print with provided you have a heated and well levelled bed. A good starting point for a successful print is to have your hot end around 235 degrees and your hot bed around 70 degrees. All AURARUM filaments are 100% Australian made right here in Melbourne, Victoria.
- Add to cart
-
- 1.75mm filament
Aurarum PETG 3D Printer Filament – Brown 1.75mm 1Kg
- AUD25.56 - AUD31.95 Inc GST
- Aurarum PETG is a moderately easy material to print with provided you have a heated and well levelled bed. A good starting point for a successful print is to have your hot end around 235 degrees and your hot bed around 70 degrees. All AURARUM filaments are 100% Australian made right here in Melbourne, Victoria.
- Add to cart
Shop
This is where you can browse products in this store.
